Projektor Panasonic PT-DZ10KEJ
|Wysyłka w ciągu||24h|
|Power supply||120 V, 220-240 V AC, 50/60 Hz|
|Power consumption||120 V AC||925 W (1,010 VA)
(0.2 W with standby mode set to eco.*1
6 W with standby mode set to normal. Both with fan stopped.)
|220-240 V AC||900 W (980 VA)
(0.3 W with standby mode set to eco.*1
9 W with standby mode set to normal. Both with fan stopped.)
|Dissipation BTU||120 V: 3,157 BTU/hour (without light output: 3,012 BTU/hour). 220–240 V: 3,072 BTU/hour (without light output: 2,927 BTU/hour)|
|DLP™ chip||Panel size||24.4 mm (0.96 in) diagonal (16:10 aspect ratio)|
|Display method||DLP™ chip x 3, DLP™ projection system|
|Pixels||2,304,000 (1,920 x 1,200) x 3, total of 6,912,000 pixels|
|Lens||Optional powered zoom/focus and fixed-focus lenses|
|Lamp||355 W UHM lamps (NORMAL mode) x 2|
|Screen size (diagonal)||1.78 –25.4 m (70–1,000 in), 1.78 –15.24 m (70–600 in) with the ET-D75LE8, 16:10 aspect ratio|
|Brightness*2||10,600 lm (dual-lamp)|
|Contrast*2||10,000:1 (full on/off, with DYNAMIC IRIS set to "3")|
|Resolution||1,920 x 1,200 pixels|
|Scanning frequency||SDI||3G-SDI||SMPTE ST 424 compliant, [RGB 4:4:4 12-bit /10-bit] 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p [YPBPR 4:2:2 10-bit] 1080/50p, 1080/60p,|
|HD-SDI||SMPTE ST 292 compliant, [YCBCR 4:2:2 10-bit] 720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p|
|SD-SDI||SMPTE ST 259 compliant, [YCBCR 4:2:2 10-bit] 480i, 576i|
|HDMI/DVI-D||480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, VGA (640 x 480)–WUXGA*4 (1,920 x 1,200), compatible with non-interlaced signals only, dot clock: 25–162 MHz|
|RGB||fH: 15–100 kHz, fV: 24–120 Hz, dot clock: 20–162 MHz|
|YPBPR (YCBCR)||fH: 15.75 kHz, fV: 60 Hz [480i(525i)]
fH: 15.63 kHz, fV: 50 Hz [576i(625i)]
fH: 45.00 kHz, fV: 60 Hz [720(750)/60p]
fH: 33.75 kHz, fV: 60 Hz [1035/60i]
fH: 28.13 kHz, fV: 50 Hz [1080(1125)/50i]
fH: 27.00 kHz, fV: 24 Hz [1080/24p]
fH: 33.75 kHz, fV: 30 Hz [1080/30p]
fH: 56.25 kHz, fV: 50 Hz [1080/50p]
fH: 31.50 kHz, fV: 60 Hz [480p(525p)]
fH: 31.25 kHz, fV: 50 Hz [576p(625p)]
fH: 37.50 kHz, fV: 50 Hz [720(750)/50p]
fH: 33.75 kHz, fV: 60 Hz [1080(1125)/60i]
fH: 28.13 kHz, fV: 25 Hz [1080/25p]
fH: 27.00 kHz, fV: 48 Hz [1080/24sF]
fH: 67.50 kHz, fV: 60 Hz [1080/60p]
|Video/Y/C||fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60], fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]|
|Optical axis shift*5||Vertical||±55 % (±44 % with the ET-D75LE6) from center of screen (powered)|
|Horizontal||±20 % (±15 % with the ET-D75LE6) from center of screen (powered)|
|Keystone correction range||Vertical: ±40°*6, horizontal: ±15°|
|Installation||Ceiling/floor, front /rear, portrait*7|
|Terminals||SDI IN||BNC x 1 (3G/HD/SD-SDI)|
|3D SYNC IN/OUT||-|
|3D SYNC OUT||-|
|DVI-D IN||DVI-D 24-pin x 1 (DVI 1.0 compliant, compatible with HDCP, compatible with single link only)|
|HDMI IN||HDMI 19-pin x 1 (Deep Color, compatible with HDCP)|
|RGB 1 IN||BNC x 5 (RGB/YPBPR/YCBCR/YC x 1)|
|RGB 2 IN||D-Sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR x 1)|
|VIDEO IN||BNC x 1 (composite video)|
|SERIAL IN||D-sub 9-pin (female) x 1 for external control (RS-232C compliant)|
|SERIAL OUT||D-sub 9-pin (male) x 1 for link control|
|REMOTE 1 IN||M3 x 1 for wired remote control|
|REMOTE 1 OUT||M3 x 1 for link control (for wired remote control)|
|REMOTE 2 IN||D-sub 9-pin (female) x 1 for external control (parallel)|
|LAN||RJ-45 x 1 (for network connection, 10Base-T/100Base-TX, compliant with PJLink™)|
|Cabinet materials||Molded plastic|
|Dimensions (W x H x D)||530 x 200*8 x 548.5 mm (20-7/8 x 7-7/8*8 x 21-19/32 in) (optional lens not included)|
|Weight*9||Approximately 24 kg (52.9 lbs) (optional lens not included)|
|Operation noise*2||43 dB (dual lamp operation with lamp NORMAL mode), 37 dB (dual lamp operation with lamp ECO mode)|
|Operating environment||Operating temperature: 0–45°C (32–113°F)*10, operating humidity: 10–80 % (no condensation)|
|Applicable software||Logo Transfer Software, Multi Projector Monitoring & Control Software|
|Supplied accessories||Power cord with secure lock, wireless/wired remote control unit, batteries (R6/AA type x 2)|
|NOTE||* Product numbers vary depending on the market. The general guideline is as follows: The product number in North America and Taiwan is PT-DW11KU and PT-DZ10KU. The product number in Europe (except for those shipped directly to Europe), CIS, Asia (except Taiwan), Oceania, Middle East, and Africa is PT-DW11KE and PT-DZ10KE.
The product number for the direct shipments to Europe is PT-DW11KEJ and PT-DZ10KEJ.
*1 When the STANDBY MODE is set to ECO, network functions such as power on over the LAN network will not operate, and the serial output terminal cannot be used. Also, only certain commands can be received for external control using the serial terminal.
*2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*3 In Portrait mode, the maximum brightness becomes 9,600 lm.
*4 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*5 Optical axis shift cannot be operated with the ET-D75LE50.
*6 ±22° with the ET-D75LE50, ±28° with the ET-D75LE6.
*7 Requires optional lamp units for portrait mode.
*8 With legs at shortest position.
*9 Average value. May differ depending on the actual unit.
*10 The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when the FAN CONTROL is set to HIGH ALTITUDE MODE (for altitudes from 1,400 m to 2,700 m (4,593 ft to 8,858 ft) above sea level). When the projector is used with the ET-SFD320 Smoke Cut Filter, the operating temperature range is 0 °C to 35 °C (32 °F to 95 °F), and the projector cannot be used in places at high altitude. WITH THE ET-LAD320P/LAD320PW MOUNTED FOR THE PORTRAIT MODE: The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F). The operating temperature range is 0 °C to 35 °C (32 °F to 95 °F) when the FAN CONTROL is set to HIGH ALTITUDE MODE (for altitudes from 1,400 m to 2,700 m (4,593 ft to 8,858 ft) above sea level). When the projector is used with the ET-SFD320 Smoke Cut Filter, the operating temperature range is 0 °C to 30 °C (32 °F to 86 °F), and the projector cannot be used in places at high altitude.
|NOTES ON USE||1 Do not install the projector in locations that are subject to excessive water, humidity, steam, or oily smoke. Doing so may result in fire, malfunction, or electric shock.
2 The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a loud sound, or fail to illuminate, due to impact or extended use.
3 The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions:
• Never place objects on top of the projector while it is operation.
• Make sure there is an unobstructed space of 500 mm (19-11/16 inches) or more around the projector's exhaust openings.
• Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection. When stacking projector units, be sure to provide the amount of space indicated between them. These space requirements also apply to installation where only one projector unit is operating at one time and the other unit is used as a backup.
• If the projector is placed in a box or enclosure, temperature of the air surrounding the projector must be between 0 °C (32 °F) and 40 °C (104 °F). Also make sure the projector’s intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake.
4 If the projector is to be operated continuously 24 hours a day / 7 days a week, use the dual-lamp optical system’s alternating lamp operation function (Lamp Relay mode). The projector can be operated continuously 24 hours a day / 7 days a week in dual-lamp operation mode. Allow a minimum of two hours per week of non-operation time per lamp if using the dual-lamp operation mode.
5 The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.
• The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and usage conditions.
• The brightness of the lamp will gradually decrease with use.
• The usage environment affects the lamp replacement cycle.
6 Because the ET-D75LE50 is a fixed short-throw lens, the lens shift function cannot be used with it.
7 Due to natural characteristics of lamps, screen brightness may vary (flicker). This is not an indication of faulty lamp performance.
- Oferty dla specjalistów